Constructing Blouse 303 (with bonus Photoshop/Gimp tutorial)

Fair warning, this is going to get nerdy so if you like your sewing sans-geek then click here for the pretty photos post instead ;)

You can see from my photos in the last post that my silk crepe had a wide pattern repeat of two different dots and lines. It’s a really cool pattern and what promoted me to pick it up off the remnant table even though it was only about 1.1 meters worth. With such a limited amount of fabric the challenge is always pattern placement and I really had zero room for error plus I wanted to make the most of the design.

So, in keeping with my nerdy sewing tendencies I sat down at my computer and ran through the options…now this might seem a little bit over-the-top for most of you but I had fun doing it and that’s really what matters right?

I’m going to cover the contruction of this blouse near the end of this post but first I’ll share a kind of advanced tutorial following on from my Photoshop & Gimp visualisation tutorials. I’m going to briefly cover some more advanced techniques. I’ll show you how I cheated a tiny line image to make it workable and how to get the correct scale for your fabric print. If you like what you see and you’re keen to do something similar you should read my original tutorials first.

Hi-res scan

Tiny Images: Because my magazine line drawing image was so tiny (about 1.5cm x 1.5cm) I scanned it at 600dpi. This is a good trick to make the image appear larger. I say “appear” because your image is still really actually the same size but you can view it larger without it looking blurry if it is at a higher resolution, plus when you drop your fabric into the image it won’t get all pixellated.

Your scanner will probably freak out at this point and bring up a message asking “are you sure?!”, suggesting a lower dpi and threatening that it will take a long time etc blah blah but just tell it to do as it’s told, it’s only a small image and the world really won’t come to a grinding halt if you go around recklessly scanning things at a high-resolution!

"Clean " fabric photo

Scaling the fabric: For this example my fabric scale was really important for accuracy. I took two photos of my fabric, the first (above) is the “clean” shot you would normally take to use in the manipulation, the second (below) is for scale.

Fabric photo with pattern piece for scale

I laid the front pattern piece on the fabric, took my photo and then I bought this image into my line drawing image. You can see below my screen shot from Photoshop below. I’ve lowered the opacity of the fabric image to I could “see through” it to the line drawing, then I scaled it using the free transform/scale tool (remember that one? Ctrl + T in Photoshop or  in Gimp)

The yellow pattern piece is now about the right size. I think the proportions of the line drawing are a little off but this is close enough for me.

Next I dropped in the “clean” photo – I put the opacity of the first photo back up to 100% and lowered the opacity of the new photo. Same deal, scale it to match the first photo. When you are happy with it you can delete the “Fabric for Scale” layer and put the final fabric layer’s opacity back up to 100% and continue on as normal.

I started with a few basic orientation trials and here are my results.

Then I got a little more clever (or nerdy, take your pick) and selected my 3 favourites to add in a bit more details. I’m going with A, B & C and now I’m going to be a bit more realistic about my pattern placement. I laid the actual pattern pieces out on my fabric as I went so that after cutting out the front and back I could see what bits would be left over for the sleeves and collar.

I think this image above corresponds with option B.2 below – to make these more complex images I just made multiple copies of the fabric layer and moved and rotated them to fill in the sleeves and neck line.

I still couldn’t decide which I liked but it did give me a starting point to do some old school laying the fabric over Scarlett and I looked at these along with my three favourites and then I had a revelation: the black dots at waist height could have the bonus of creating a slimming effect!  (I know image C looks exaggerated in these photos, that’s my pins, not the light waves magically bending to make Scarlett’s waist smaller – she has dials to do that anyway, hehe ;))

Final photoshop image

The quick among you will have already noticed that the final blouse didn’t end up exactly like this, but it’s pretty close. I originally laid the body out higher up on the my fabric thinking that I could also get the collar out of the lines but in the end I moved the whole thing down to make the most of the darker spots and their (hopefully) waist minimising properties. This meant the neck ended up out of the big white spots but I actually like it better this way.

So, on to the construction. It’s quite an easy blouse to put together, the most complicated looking part is the sleeves and when you break them down they really aren’t that complicated at all.

Pattern Layout for sizes 38 & 42 - which I didn't really follow

All pieces are laid out on a flat piece of fabric (not folded) – ourela means selvages – this piece is shown as 150cm wide and you need 0.9/1.0/1.2 meters depending on which size you cut and a little bit more if your fabric is a narrower width but I find Manequim are quite generous with their pattern layouts.

Don’t forget to add your seam allowances before you cut out.

  • 11 – Blouse front (x1 on the fold)
  • 12 – Blouse back(x1 on the fold)
  • 13 – Sleeve cap (x2)
  • 14 – Sleeve cuff (x2)
  • A – Collar (x1 rectangle 8cm x 70/74/78cm depending on the size you cut)
  • B – I have no idea….and I didn’t find out during construction either…any suggestions? Anyone know Portuguese? It’s labelled as Alça.

So as per usual my first step is to address any pleats and darts. We have one in each sleeve cap and another at the neck of the front pattern piece. The only pleat I didn’t pre-sew was the once shown on the sleeve cuff.

Side seams come next:

Here is the body of the blouse on Scarlett – my seams are sewn inside-out in preparation for “Frenching” them. I don’t think that’s a real term but I’m using it ;)

You can probably tell that there is a lot of extra fabric outside the seam line. I discovered right away a flaw in my plan for using French seams. I always adjust the side seams of my tops on me as I sew. I cut a pattern out to fit my hips/bust (in this case, Manequim size 42) but my waist is generally smaller. If I don’t grade it in at the time of cutting it I usually just adjust on the fly as I sew. You just can’t do that with French seams, once the second line of stitching is done that’s it! So I basted the top on myself inside out and took it in until I was happy with the overall fit.

I did it a little at a time because the lack of closures means I had to leave enough ease to be able to get in and out of it. Once I was happy I trimmed the seams down in preparation for the “Frenching”. Yup, I am definitely making “Frenching” a part of my usual sewing vocabulary.

"Frenching" the seams

So, on to the sleeves:

If you click to enlarge the photo above about you might be able to just make you the numbers at the corners of each piece. The great thing about Manequim patterns is they number their seams so you can easily work out which piece to attach to which. Here you can see the sleeve cap with the cuff below. You fold the sleeve cuff in half and line up the numbers 1′s. The numbers 3 & 4 at the top relate to the shoulder points on the front and back pieces we assembled earlier and will help you put the each sleeve on its correct side. For good measure the number 5 helps with this too so take the time to trace and if you pay attention to them and it will save you many tears later on.

So here they are in fabric, you can now stitch seam number 1, attaching the cuff to the sleeve cap.

Sew the pleat in the cuff next by folding the cuff up at the marking, right sides together, and sew a line of stitching as marked.

Here is how it looks from the inside...

...and the final sleeve from the right side

You can attach your sleeves now, use the numbers to help you line things up.

Above you can see (on the left) the sleeve attached pre “Frenching”, and (on the right) finished.

Join the ends of the neck rectangle together and fold in half, wrong sides together.

Now here is where I made the mistake with the neck and had to unpick it twice! I did that silly thing where my brain suggests something while I am sewing and I completely ignore it only to concede later on that it was correct from the start and then I end up unpicking something.

In this case it was a whispered suggestion to interface the standup collar since the silk is so flimsy there was no way it would stand up by itself. But the other voice, yes sometimes there are two, said, “don’t be silly, interfacing will look terrible, you’ll be able to see it and besides, the collar will probably be helped by the French seams”.

When I tried on the top for the first time after attaching the collar I noticed immediately that voice #1 had been correct. The stand-up collar was actually a floppy collar.

So I marked my hem (the reason for the try on) and then sat in the sunshine unpicking the collar. I wasn’t looking forward to this because the fraying was getting pretty bad.

Interfacing and I aren’t really enemies but I wouldn’t say we are friends either. I do use interfacing when a pattern calls for it but that of course means I read it in the instructions…in English ;) I am learning slowly more about interfacing and this was a pretty good learning moment for me. Firstly to actually use interfacing, and secondly, not to over do it. My first choice was a waaaay- to-stiff fusible and I was starting to look like previously mentioned HBO cat.

Back to the sunshine drenched lounge I went with the blouse and my unpicker.

The fraying was by now almost completely un-salvageable (cue evidence above) and I knew I would have to alter my seam lines to compensate but in the end it ended up being a good thing.

So I was more careful with my second interfacing selection. I tested several options with my scrap left overs and it turned out a super lightweight non-fusible was the best option. I wanted the collar to stand up but not look like it was being stood up if that makes any sense :)  so I went to work.

There were two bonuses in all this. The first was that as I tried on the top I noticed that the back rode up a little too high in the neck line and at the sleeves so it meant I could correct this fault at the same time as re-attaching the collar. Secondly, due to the horrid fraying the collar height ended up reduced by about 5 millimeters. Now that doesn’t sound like a lot but I much prefer the new height.

After attaching the collar I hemmed the bottom by overlocking the lower edge, folding to the inside and I chose to top-stitch it in place.

In other exciting news: Patterns!

Excuse the crappy cell phone pictures, I was too excited and too late for work to get out the “real” camera.

I made an order at BMV.com when they had their sale just over a week ago. I really wasn’t expecting them to arrive so quickly. My last order I made from Western Australia took almost 3 weeks and these ones took significantly less, 9 days to be exact. In fact they got here so quick they ended up a little wet from being out on the door step over night since I didn’t bother to check for them. But they will be OK, it’s just on the bottom edges of the envelopes.

Blouse 303 from Manequim 625

It’s probably about time I showed you all some sewing. I have managed to drag myself away from the biggest party NZ has seen for a while to finally take more pics of my newest blouse. I finished it about 3 weeks ago and I’m going to put my hand up now and say I know these photos are really bad but I’ve taken them three times and just can’t seem to like them so I’m giving up and posting anyway :)

If it looks like these photos were taken on two different days it's because they were

The contrast is terrible, I know, plus I managed to get the sliding door in all of them, which I subsequently had to crop out so the composition is pretty awful too…the wind didn’t help either, I’d get myself all settled, push the remote button, wait for the beeps and then, wooosh! Gah, who’d of thought, wind? In Wellington?!

Because everyone likes to see an out-take...

I don’t know, for some reason I am hating the photos I take of myself lately, but I’ll get over it because I LOVE this blouse…so on to the details:

It is from Manequim 625 and is#303. I liked it as soon as this magazine arrived in my hot little hands and I chose to use this amazing silk crepe that I got from the  “Remnant Table of Endless Inspiration” at my last trip to Potters (sigh, I miss that shop!).

You might have noticed, although I haven’t mentioned it officially, I am doing a little bit of stash busting. The Esther cardi knit was from my stash and this blouse was the next one - (Belated) Birthday Dress and the following project are in this category as well.

I got this 149cm x 1.1m length for $10, a bargain yes, but I was scared to ruin it so I let it mature nicely in my stash and then I put my brave on and cut into it last month. If you are in Perth and have not been to Potter’s yet, then what are you doing? Go, go now, you will not be disappointed.

This is only the second silk item I have made, and my first in a crepe. I discovered quite quickly that working with this fabric was a lot of fun. It frayed right in front of my eyes, even while it was just sitting on the table it was merrily fraying itself away to nothing. But I loved the print so I was determined to make it work. To be honest I think it took me longer to work out how to place the pattern pieces to make the most of the print than it did to eventually sew it up. I used Photoshop to help me finally decide how to do it and I’ve started a post on that (along with the construction) that I’ll pop up in a day or two – it will be another of those epically nerdy posts so consider yourself forewarned ;)

Despite the fraying and the Photoshopping the construction went pretty smoothly, apart from the fact that I had to unpick the standing collar three times. It was completely my silly fault and in the end it turned out for the best because it meant it got a tad shorter and after my first try-on I was starting to feel a bit like HBO cat.

And here are a few more detailed shots.

Standing collar and front pleat detail

Sleeve detail

After cutting out my pieces I realised just how sheer my fabric was, this would mean I needed french seams, which was not really big deal. I’ve only ever done them once before (on my BurdaStyle Book blouse no less) and they worked out ok, plus Carolyn had just posted up a timely reminder tutorial which I had a skim over to refresh the memory. Here is a sleeve close-up inside out, you can see the French seams. I’m quite proud of how they turned out and my construction skills are definitely improving. I think the French seam also helps strengthen the seams and protects the interior of the silk during wear and washing.

Inside out detail

In other sewing related news:

Exciting: I have (99.9%) finished the (Belated) Birthday Dress and I am so happy with it! The hem got pressed today and I just have to decide whether to top-stitch it (as per the instructions) or get out the needle and thread and hand stitch it up, which I am terrible at…but the fabric weave/print will help hide my hand-sewing sins and whichever way I chose to go there will be photos next weekend.

Less exciting: The Gok coat is also complete, but I’m not sure if I like it. I will share pictures with you before I decide what to do with it. I think it can be saved, the question is: “Can I be bothered before Summer arrives…?”

Next in-line: I guess I should really try to finish the Forever Jeans…thread arrived from eBay last month – yes, that means I gave up on Spotlight and bought it of all places from England! But I guess that all depends on how soon my pattern splurge purchases from BMV arrives ;)

Patrones 303 (April 2011)

Apparently I did manage to scan another magazine, Patrones 303, which is weird because I have zero recollection of doing so but the flash drive never lies so here it is :)

There wasn’t a huge amount in this issue that grabbed me but I do like the look of this green dress. I’m a bit iffy about the whole one-shoulder thing, there are quite a few in this issue and Burda seem to be obsessed with it lately as well, still, this dress is quite stunning.

.

.

.

The central section contains several different skirts and tops. They are all quite youthful and fun and I really like the soft colour combinations. We are heading into winter here in Wellington and while autumn is clinging on (yay) these are definitely getting filed away until warmer weather finally returns. But I don’t mind, I quite like winter sewing and I have a few ufo’s to catch up on that will be perfect while these patterns ‘mature’ on the shelf ;)

I just had to stick these shorts in here because Patrones do seem to have an unhealthy obsession with the bloomer style pants and shorts, there’s usually at least one pair in each issue. I’m not going to say much more because I know my fashion sense is not entirely on the level so some of you might has spotted these and added them to the top of your ‘to-sew’ list but personally I’m putting these in the same category as Jeggings, Ugg boots in public and Crocs…please, just say ‘no’.

'no'

If you are keen for some cute bloomers as underwear why don’t you check out Colette Patterns free download: Madeline Mini Bloomers, very cute.

Another one shoulder item but I am more interested in the pants, a slim-fit 3/4-length cargo pant which I’d like to make, perfect for the last few autumn traps up Mt Kau Kau or out to the Orongorongo Valley.

.

.

.

..

I have received this months issue but have no way to scan it at the moment. Its full of beachy goodness, lots of flowy summer dresses and a blouse with the largest pleated cuffs you’ve ever seen so I promise to get it scanned and uploaded as soon as I can for a giggle.

I have  good news to share about the container that contains my life (which you are probably all sick of hearing about) it arrives today and just has to clear customs, yay! I also picked up the keys to our rental property this morning so now I just have to beat husband to the bigger of the spare rooms ;) I think they are actually both the same size however one does have significantly more power points. However I am used to subsisting with a single power point so even the room that has one double will seem like a electrified luxury!